塑性変形条件の英語

相変態をともなう温度変化中の試験片の変形量を検出し、引張、圧縮条件下それぞれで異なる変態塑性係数を同時に同定することができる変態塑性係数同定方法を提供する。例文帳に追加

To provide a method for identifying transformation plasticity coefficients capable of detecting deformation volumes of test pieces under temperature change with phase transformation and capable of simultaneously identifying the transformation plasticity coefficients that are different under tensile and compression conditions respectively. - 特許庁

弾性仕事率(％)＝弾性変形の仕事量×100／(塑性変形の仕事量＋弾性変形の仕事量)［評価条件］ダイヤモンド圧子を用いた微小表面硬度計、温度22℃、相対湿度55％の環境条件下、一定負荷速度で圧子を押し込んで全仕事量(負荷過程)と弾性変形の仕事量(除荷過程)を測定。例文帳に追加

In the evaluation method, by a load-unloading test using a diamond indenter, the indenter is pushed in and total workload (load process) and workload (unloading process) of elastic deformation are measured under an environmental condition having a temperature of 22°C and a relative humidity of 55%, and the elastic power is determined by equation: (elastic power (%))=(workload of elastic deformation)×100/(total workload). - 特許庁

被覆膜の表面に適切な条件の下でショットピーニングなどを施すことで、基材の表層部および被覆膜のいずれか一方のみを簡便に塑性変形させることができる。例文帳に追加

Only either one of the surface layer part of the base material and the coating film can be easily plastic deformed by applying shot-peening to a surface of the coating film under appropriate conditions. - 特許庁

この複合熱可塑性樹脂組成物を、金型温度が当該樹脂組成物の熱変形温度より５〜５０℃高い条件で射出成形して得られる成形品。例文帳に追加

The molding is obtained by injection molding the composite thermoplastic resin composition at a mold temperature 5-50 °C higher than the heat deformation temperature of the resin composition. - 特許庁

従来の熱可塑性エラストマーに比べ、高温の条件下でも変形が生じず、充分な機械的強度を保持し、高温滅菌にも耐える医薬・医療用材料を提供する。例文帳に追加

To obtain a medicinal and medical material capable of holding a sufficient mechanical strength and withstanding even high-temperature sterilization without causing the deformation even under high-temperature conditions as compared with that of a conventional thermoplastic elastomer. - 特許庁

高温高湿条件下に長期間放置した場合にも、現像ローラの表面に塑性変形が生じにくい電子写真用プロセスカートリッジを提供すること。例文帳に追加

To provide an electrophotographic process cartridge hardly causing plastic deformation on the surface of a developing roller, irrespective of a long-term neglect under a high temperature/humidity condition. - 特許庁

高面圧ー高ひずみ条件下での荷重支持状態において、端部に位置する鋼板の塑性変形や被覆ゴムの異常な膨れなどを防止する。例文帳に追加

To prevent a plastic deformation of a steel plate and an abnormal blister of the covered rubber which are located in an end in the load support condition under the high face pressure and the high distortion conditions. - 特許庁