Surface hardening by strain induced martensitic transformation | Production Engineering
Skip to main content
Springer Nature Link
Log in

Surface hardening by strain induced martensitic transformation

  • Production Process
  • Published:
Production Engineering Aims and scope Submit manuscript

Abstract

The hardness and fatigue strength achieved by strain hardening are normally noticeable lower than those attained by thermal or thermochemical heat treatments. Strain or deformation induced martensitic transformation of residual austenite can increase the strength achieved by mechanical surface hardening processes considerably. In this paper, an approach is presented where workpieces with a high content of metastable austenite are used for hardening the surface layer. The microstructure has to be sufficiently stable, in order to ensure that the material can be machined without being changed by strain induced transformation of the residual austenite. After machining, high Hertzian contact stresses are introduced by deep rolling, so that a strain induced martensitic transformation of the residual austenite takes place. At the same time deep rolling produces the surface finish of the part. By this method, a surface hardening without a heat treatment process within the production line can be realized. A conceivable use of this method could be the production of bearings or guideways.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Subscribe and save

Springer+ Basic
¥17,985 /Month
  • Get 10 units per month
  • Download Article/Chapter or eBook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price includes VAT (Japan)

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11

Similar content being viewed by others

References

  1. El-Axir MH (2000) An investigation into deep rolling. Int J Mach Tools Manuf 40:1603–1617

    Article  Google Scholar 

  2. Hirsch T, Wohfahrt H, Macherauch E (1987) Fatigue strength of case hardened and shot peened gears. In: Wohlfahrt H, Kopp R, Vöhringer O (eds) Shot peening: science, technology, application. DGM Informationsgesellschaft, Oberursel pp 547–560

    Google Scholar 

  3. Schuhbauer H-G, Bäuerle H, Müller-Stock H-W (1991) Schwingfestigkeitssteigerung schwerer Maschinenbauteile durch Schlagverfestigen. Konferenz-Einzelbericht: Moderne Fertigungs-technologien zur Lebensdauersteigerung, 17. Vortragsveranstaltung des DVM-Arbeitskreises Betriebsfestigkeit, pp 53–64

  4. Röttger K (2003) Walzen hartgedrehter Oberflächen. Dissertation Dr.-Ing. RWTH Aachen. Shaker Verlag, Aachen

    Google Scholar 

  5. Brinksmeier E, Roth P (1990) Hochdruck-Wasserstrahlen—ein neues Verfahren zur mechanischen Randzonenverfestigung. HTM 45:300–306

    Google Scholar 

  6. Tönshoff H-K, Kroos F, Marzenell C (1997) Improving fatigue strength of finished case hardened components by high-pressure water peening. Prod Engineer 4:67–72

    Google Scholar 

  7. Papshev DD (1985) Effektive Methoden der mechanischen Oberflächenverfestigung.Mitteilungen aus dem Institut für Leichtbau und Ökonomische Verwendung von Werkstoffen. Dresden 24:40–43

    Google Scholar 

  8. Schwarmann L (1994) Methoden zur Steigerung der Lebensdauer genieteter Fügungen im Flugzeugbau (Speziell das Aufdornverfahren). Konferenz-Einzelbericht: Fügen im Leichtbau, 20. Vortragsveranstaltung des DVM-Arbeitskreises Betriebsfestigkeit, pp 227–232

  9. Plappert S (2001) Zur Steigerung der Dauerfestigkeit dickwandiger, quergebohrter Rohre durch autofrettage. Dissertation, University of Erlangen-Nürnberg

  10. Greuling S, Seeger T, Vormwald M (2006) Autofrettage innendruckbelasteter Bauteile. Materialwissenschaft und Werkstofftechnik 37:233–239

    Article  Google Scholar 

  11. Reissner J (1999) Innovation potential of materials and their impacts on processing in forming technology. Advanced technology of plasticity, vol 1. Proc of the 6th ICTP, Sept 19–24, pp 409–418

  12. Wei X, Xie Q, Zhang M, Li L, Wollants P (2007) Influence of strain-induced retained austenite transformation on the dynamic tensile behaviour of TRIP-aided steels. Steel Res Int 78:554–559

    Google Scholar 

  13. Razim C (1968) Über den Einfluß von Restaustenit auf das Festigkeitsverhalten einsatzgehärteter Probekörper bei schwingender Beanspruchung. HTM 23:1–8

    Google Scholar 

  14. Kloos K-H, Kaiser B, Adelmann J (1989) Einfluß einer mechanischen Randschichtverfestigung auf die Ermüdungseigenschaften einsatzgehärteter Proben und Zahnräder. In: Broszeit E, Steindorf H (eds) Mechanische Oberflächenbehandlung—Festwalzen, Kugelstrahlen, Sonder-verfahren. DGM Informationsgesellschaft, Oberursel

  15. Tamura I (1982) Deformation-induced martensitic transformation and transformation-induced plasticity in steels. Mater Sci 16:245–253

    Google Scholar 

  16. Weiß A, Gutte H, Scheller P (2006) Deformation induced martensite formation and ist effect on transformation induced plasticity (TRIP). Steel Res Int 77:727–732

    Google Scholar 

  17. Onodera H, Goto H, Tamura I (1976) Effect of volume change on martensitic transformation induced by tensile or compressive stress in polycristalline iron alloys. Proc. 1st JIM Int Symp, Kobe, Japan, pp 327–332

  18. Bayerlein M, Christ H-J, Mughrabi H (1989) Plasticity-induced martensitic transformation during cyclic deformation of AISI 304L stainless steel. Mater Sci Engineer A114:L11–L16

    Article  Google Scholar 

  19. Oettel H, Martin U (2006) The nature of the TRIP-effect in metastable austenitic steels. Int J Mater Res 97:1642–1647

    Google Scholar 

  20. Ganesh SR, Padmanabhan KA (1994) Influence of martensite formation and grain size on room temperature low cycle fatigue behaviour of AISI 304LN austenitic stainless steel. Mater Sci Technol 10:614–620

    Google Scholar 

  21. Garbrecht M (2006) Mechanisches Randschichthärten in der Fertigung. Dissertation Dr.-Ing. Universität Bremen, Shaker-Verlag, Aachen, ISBN 3–8322–5262–2

  22. Lecroisey F, Pineau A (1972) Martensitic transformations induced by plastic deformation in the Fe-Ni-Cr-C system. Metall Trans 3:387–396

    Article  Google Scholar 

  23. Murr LE, Staudhammer KP, Hecker SS (1972) Effects of strain state and strain rate on deformation-induced transformation in 304 stainless steel: Part II. Microstructural study. Metall Trans 13A:627-663

    Google Scholar 

Download references

Acknowledgments

The authors thank for the projects funding by Bundesministerium für Wirtschaft und Technologie (BMWi) via Arbeitsgemeinschaft industrieller Forschungsvereinigungen (AiF) and the assistance of the working commitees “Fertigungstechnik” and “Werkstoffe” of Forschungsvereinigung Antriebstechnik e.V. (FVA) and Arbeitsgemeinschaft Wärmebehandlung und Werkstofftechnik e.V. (AWT).

Author information

Authors and Affiliations

  1. Foundation Institute of Material Science, Badgasteiner Str. 3, 28359, Bremen, Germany

    E. Brinksmeier, M. Garbrecht, D. Meyer & J. Dong

Authors
  1. E. Brinksmeier
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. M. Garbrecht
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. D. Meyer
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. J. Dong
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to M. Garbrecht.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Brinksmeier, E., Garbrecht, M., Meyer, D. et al. Surface hardening by strain induced martensitic transformation. Prod. Eng. Res. Devel. 2, 109–116 (2008). https://doi.org/10.1007/s11740-007-0060-6

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11740-007-0060-6

Keywords

Search

Navigation