组网需求
集中式转发架构下，AC旁挂在L3 switch上，L3 switch做DHCP server为AP、Client和Host分配IP地址。需要实现无线客户端Client通过AP连接到AC上，并能与有线客户端Host互相访问，具体要求如下：
无线客户端Client通过VLAN 200接入网络，有线客户端Host通过VLAN 300接入网络；
AC属于VLAN 100，AP属于VLAN 400，AC和AP之间跨三层网络建立连接。
L2 switch 1通过PoE方式给AP供电。
配置思路
- 在L3 switch上开启DHCP server功能，AP、无线客户端Client和有线客户端Host都能通过DHCP server自动获取IP地址。
- 在AC上配置缺省路由下一跳为L3 switch。
- 在DHCP server上配置AP通过option方式获取AC的IP地址完成三层注册。
- 在L2 switch 1上开启PoE功能，为AP设备供电。
- 在AC上配置无线服务，确保Client可以通过配置的无线服务接入网络。
- 配置AP的序列号时请确保该序列号与AP唯一对应，AP的序列号可以通过AP设备背面的标签获取。
- 在L2 switch 1上开启PoE功能，为AP设备供电。
- 配置L2 switch 1和AP相连的接口为Access口。
配置注意事项
配置AP的序列号时请确保该序列号与AP唯一对应，AP的序列号可以通过AP设备背面的标签获取。
在L2 switch 1上开启PoE功能，为AP设备供电。
配置L2 switch 1和AP相连的接口为Access口。
配置AC
(1) 配置AC的接口
# 创建VLAN 100及其对应的VLAN接口，并为该接口配置IP地址。AP将通过DHCP option43方式获取该IP地址与AC建立CAPWAP隧道。
<AC> system-view
[AC] vlan 100
[AC-vlan100] quit
[AC] interface vlan-interface100
[AC-Vlan-interface100] ip address 192.168.10.1 255.255.255.0
[AC-Vlan-interface100] quit
# 创建VLAN 200，AC需要使用该VLAN转发无线客户端数据报文。
[AC] vlan 200
[AC-vlan200] quit
# 配置AC和L3 switch相连的接口GigabitEthernet1/0/1为Trunk类型，禁止VLAN 1报文通过，允许VLAN 100和VLAN 200通过。
[AC] interface gigabitethernet 1/0/1
[AC-GigabitEthernet1/0/1] port link-type trunk
[AC-GigabitEthernet1/0/1] undo port trunk permit vlan 1
[AC-GigabitEthernet1/0/1] port trunk permit vlan 100 200
[AC-GigabitEthernet1/0/1] quit
(2) 配置三层路由
# 配置AC缺省路由下一跳为L3 switch的IP地址为192.168.10.83。
[AC] ip route-static 0.0.0.0 0 24 192.168.10.83
(3) 配置无线服务
# 创建无线服务模板1，并进入无线服务模板视图。
[AC] wlan service-template 1
# 配置SSID为service。
[AC-wlan-st-1] ssid service
# 使能服务模板。
[AC-wlan-st-1] service-template enable
[AC-wlan-st-1] quit
(4) 配置AP
# 创建手工AP，名称为officeap，型号名称为WA4320i-ACN。
[AC] wlan ap officeap model WA4320i-ACN
# 设置AP的序列号为210235A1GQB147031200。
[AC-wlan-ap-officeap] serial-id 210235A1GQB147031200
# 进入AP的Radio 1视图，并将无线服务模板1绑定到Radio 1上，并指定客户端上线的VLAN为VLAN 200。
[AC-wlan-ap-officeap] radio 1
[AC-wlan-ap-officeap-radio-1] service-template 1 vlan 200
# 开启Radio 1的射频功能。
[AC-wlan-ap-officeap-radio-1] radio enable
[AC-wlan-ap-officeap-radio-1] return配置L3 switch
(1) 配置L3 switch的接口
# 创建VLAN 100和VLAN 400，并配置IP地址，用于转发AC和AP间的CAPWAP隧道内的流量。
<L3 switch> system-view
[L3 switch] vlan 100
[L3 switch-vlan100] quit
[L3 switch] interface vlan-interface 100
[L3 switch-Vlan-interface100] ip address 192.168.10.83 255.255.255.0
[L3 switch-Vlan-interface100] quit
[L3 switch] vlan 400
[L3 switch-vlan400] quit
[L3 switch] interface vlan-interface 400
[L3 switch-Vlan-interface400] ip address 192.168.40.1 255.255.255.0
[L3 switch-Vlan-interface400] quit
# 创建VLAN 200，并为该接口配置IP地址。Client使用该VLAN接入无线网络。
[L3 switch] vlan 200
[L3 switch-vlan200] quit
[L3 switch] interface vlan-interface 200
[L3 switch-Vlan-interface200] ip address 192.168.20.1 255.255.255.0
[L3 switch-Vlan-interface200] quit
# 创建VLAN 300，并为该接口配置IP地址。Host使用该VLAN与AC建立连接。
[L3 switch] vlan 300
[L3 switch-vlan300] quit
[L3 switch] interface vlan-interface 300
[L3 switch-Vlan-interface300] ip address 192.168.30.1 255.255.255.0
[L3 switch-Vlan-interface300] quit
# 配置L3 switch和AC相连的接口GigabitEthernet1/0/1为Trunk类型，允许VLAN100和VLAN 200通过。
[L3 switch] interface gigabitEthernet 1/0/1
[L3 switch-GigabitEthernet1/0/1] port link-type trunk
[L3 switch-GigabitEthernet1/0/1] port trunk permit vlan 100 200
[L3 switch-GigabitEthernet1/0/1] quit
# 配置L3 switch和L2 switch1和相连的接口GigabitEthernet1/0/2为Trunk类型，禁止VLAN 1报文通过，允许VLAN 400通过。
[L3 switch] interface gigabitEthernet 1/0/2
[L3 switch-GigabitEthernet1/0/2] port link-type trunk
[L3 switch-GigabitEthernet1/0/2] undo port trunk permit vlan 1
[L3 switch-GigabitEthernet1/0/2] port trunk permit vlan 400
[L3 switch-GigabitEthernet1/0/2] quit
# 配置L3 switch和L2 switch2相连的接口GigabitEthernet1/0/3为Trunk类型，禁止VLAN 1报文通过，允许VLAN 300通过。
[L3 switch] interfac gigabitEthernet 1/0/3
[L3 switch-GigabitEthernet1/0/3] port link-type trunk
[L3 switch-GigabitEthernet1/0/3] undo port trunk permit vlan 1
[L3 switch-GigabitEthernet1/0/3] port trunk permit vlan 300
[L3 switch-GigabitEthernet1/0/3] quit
(2) 配置DHCP server
# 开启DHCP server功能。
[L3 switch] dhcp enable
# 配置DHCP地址池1为AP分配地址范围为192.168.40.0/24，网关地址为192.168.40.1。
[L3 switch] dhcp server ip-pool 1
[L3 switch-dhcp-pool-1] network 192.168.40.0 mask 255.255.255.0
[L3 switch-dhcp-pool-1] gateway-list 192.168.40.1
# 配置DHCP Option43的内容为AC的十六进制IP地址。
[L3 switch-dhcp-pool-1] option 43 hex 8007000001c0a80a01
[L3 switch-dhcp-pool-1] quit
# 配置DHCP地址池2为Client分配地址范围为192.168.20.0/24，为Client分配的DNS服务器地址为网关地址（实际使用过程中请根据实际网络规划配置无线客户端的DNS服务器地址），网关地址为192.168.20.1。
[L3 switch] dhcp server ip-pool 2
[L3 switch-dhcp-pool-2] network 192.168.20.0 mask 255.255.255.0
[L3 switch-dhcp-pool-2] gateway-list 192.168.20.1
[L3 switch-dhcp-pool-2] dns-list 192.168.20.1
[L3 switch-dhcp-pool-2] quit
# 配置DHCP地址池3为Host分配地址范围为192.168.30.0 /24，为Host分配的DNS服务器地址为网关地址（实际使用过程中请根据实际网络规划配置Host的DNS服务器地址），网关地址为192.168.30.1。
[L3 switch] dhcp server ip-pool 3
[L3 switch-dhcp-pool-3] network 192.168.30.0 mask 255.255.255.0
[L3 switch-dhcp-pool-3] gateway-list 192.168.30.1
[L3 switch-dhcp-pool-3] dns-list 192.168.30.1
[L3 switch-dhcp-pool-3] quit
配置L2 switch 1
(1) 配置L2 switch 1的接口
# 创建VLAN 400，VLAN 400为AP接入的VLAN。
<L2 switch 1> system-view
[L2 switch 1] vlan 400
[L2 switch 1-vlan400] quit
# 配置L2 switch 1与L3 switch相连的接口GigabitEthernet1/0/1为Trunk类型，禁止VLAN 1报文通过，允许VLAN 400通过。
[L2 switch 1] interface gigabitEthernet 1/0/1
[L2 switch 1-GigabitEthernet1/0/1] port link-type trunk
[L2 switch 1-GigabitEthernet1/0/1] undo port trunk permit vlan 1
[L2 switch 1-GigabitEthernet1/0/1] port trunk permit vlan 400
[L2 switch 1-GigabitEthernet1/0/1] quit
# 配置L2 switch 1与AP相连的接口GigabitEthernet1/0/2为Access类型，允许VLAN 400通过，并开启PoE远程供电功能。
[L2 switch 1] interface gigabitEthernet 1/0/2
[L2 switch 1-GigabitEthernet1/0/2] port link-type access
[L2 switch 1-GigabitEthernet1/0/2] port access vlan 400
[L2 switch 1-GigabitEthernet1/0/2] poe enable
[L2 switch 1-GigabitEthernet1/0/2] quit配置L2 switch 2
# 创建VLAN 300，VLAN 300为Host接入的VLAN。
<L2 switch 2> system-view
[L2 switch 2] vlan 300
[L2 switch 2-vlan300] quit
# 配置L2 switch 2与L3 switch相连的接口GigabitEthernet1/0/1为Trunk类型，禁止VLAN 1报文通过，允许VLAN 300通过。
[L2 switch 2] interface gigabitEthernet 1/0/1
[L2 switch 2-GigabitEthernet1/0/1] port link-type trunk
[L2 switch 2-GigabitEthernet1/0/1] undo port trunk permit vlan 1
[L2 switch 2-GigabitEthernet1/0/1] port trunk permit vlan 300
[L2 switch 2-GigabitEthernet1/0/1] quit
# 配置L2 switch 2与Host相连的接口GigabitEthernet1/0/2为Access类型，允许VLAN 300通过。
[L2 switch 2] interface gigabitEthernet 1/0/2
[L2 switch 2-GigabitEthernet1/0/2] port link-type access
[L2 switch 2-GigabitEthernet1/0/2] port access vlan 300
[L2 switch 2-GigabitEthernet1/0/2] quit
验证配置
(1) 在AC上查看到AP注册信息
# 在AC上使用命令display wlan ap all查看AP，可以看到AP的状态是R/M，表明AP已经成功注册到AC。
<AC> display wlan ap all
Total number of APs: 1
Total number of connected APs: 1
Total number of connected manual APs: 1
Total number of connected auto APs: 0
Total number of connected common APs: 1
Total number of connected WTUs: 0
Total number of inside APs: 0
Maximum supported APs: 3072
Remaining APs: 3071
Total AP licenses: 512
Remaining AP licenses: 511
AP information
State : I = Idle, J = Join, JA = JoinAck, IL = ImageLoad
C = Config, DC = DataCheck, R = Run, M = Master, B = Backup
AP name AP ID State Model Serial ID
officeap 1 R/M WA4320i-ACN 210235A1GQB147031200
(2) 在AC上查看Client信息
# 在AC上使用命令display wlan client查看在线Client，可以看到Client已经连接到AP的radio1。
<AC> display wlan client
Total number of clients: 1
MAC address User name AP name R IP address VLAN
90b9-311a-bef6 N/A officeap 1 192.168.20.3 200
(3) Host与Client可以相互ping通
# Client通过DHCP server获取到IP地址192.168.20.3，在Host上ping Client的IP地址可以ping通。同理，在Client上ping Host的IP地址也能ping通，不再赘述。
C:\Users\system32>ping 192.168.20.3 -t
Pinging 192.168.20.3 with 32 bytes of data:
Reply from 192.168.20.3: bytes=32 time=2470ms TTL=63
Reply from 192.168.20.3: bytes=32 time=2ms TTL=63
Reply from 192.168.20.3: bytes=32 time=1427ms TTL=63
Reply from 192.168.20.3: bytes=32 time=2ms TTL=63
Reply from 192.168.20.3: bytes=32 time=86ms TTL=63
Reply from 192.168.20.3: bytes=32 time=142ms TTL=63
Reply from 192.168.20.3: bytes=32 time=561ms TTL=63
Reply from 192.168.20.3: bytes=32 time=84ms TTL=63
Reply from 192.168.20.3: bytes=32 time=465ms TTL=63
Reply from 192.168.20.3: bytes=32 time=114ms TTL=63
Reply from 192.168.20.3: bytes=32 time=124ms TTL=63
Reply from 192.168.20.3: bytes=32 time=446ms TTL=63
Ping statistics for 192.168.20.3:
Packets: Sent = 12, Received = 12, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 2ms, Maximum = 2470ms, Average = 495ms
Control-C
^C
C:\Users\system32>
配置文件
• AC
#
vlan 100
#
vlan 200
#
vlan 300
#
interface Vlan-interface100
ip address 192.168.10.1 255.255.255.0
#
wlan service-template 1
ssid service
service-template enable
#
interface GigabitEthernet1/0/1
port link-type trunk
port trunk permit vlan 100 200 300
#
ip route-static 192.168.40.0 24 192.168.10.83
#
wlan ap officeap model WA4320i-ACN
serial-id 210235A1GQB147031200
vlan 1
radio 1
radio enable
service-template 1 vlan 200
radio 2
#
• L3 switch
#
dhcp enable
#
vlan 100
#
vlan 200
#
vlan 300
#
vlan 400
#
dhcp server ip-pool 1
gateway-list 192.168.40.1
network 192.168.40.0 mask 255.255.255.0
option 43 hex 8007000001c0a80a01
#
dhcp server ip-pool 2
gateway-list 192.168.20.1
network 192.168.20.0 mask 255.255.255.0
dns-list 192.168.20.1
#
dhcp server ip-pool 3
gateway-list 192.168.30.1
network 192.168.30.0 mask 255.255.255.0
dns-list 192.168.30.1
#
interface Vlan-interface100
ip address 192.168.10.83 255.255.255.0
#
interface Vlan-interface200
ip address 192.168.20.1 255.255.255.0
#
interface Vlan-interface300
ip address 192.168.30.1 255.255.255.0
#
interface Vlan-interface400
ip address 192.168.40.1 255.255.255.0
#
interface GigabitEthernet1/0/1
port link-type trunk
port trunk permit vlan 100 200
#
interface GigabitEthernet1/0/2
port link-type trunk
undo port trunk permit vlan 1
port trunk permit vlan 400
#
interface GigabitEthernet1/0/3
port link-type trunk
undo port trunk permit vlan 1
port trunk permit vlan 300
#
• L2 switch 1
#
vlan 400
#
interface GigabitEthernet1/0/1
port link-type trunk
undo port trunk permit vlan 1
port trunk permit vlan 400
#
interface GigabitEthernet1/0/2
port link-type access
port access vlan 400
poe enable
#
• L2 switch 2
#
vlan 300
#
interface GigabitEthernet1/0/1
port link-type trunk
undo port trunk permit vlan 1
port trunk permit vlan 300
#
interface GigabitEthernet1/0/2
port link-type access
port access vlan 300
poe enable
#
~
本文章为转载内容，我们尊重原作者对文章享有的著作权。如有内容错误或侵权问题，欢迎原作者联系我们进行内容更正或删除文章。
