目录
- ----- 73. 3-varible -----
- ----- 74. 4-varible (a) -----
- ----- 75. 4-varible (b) -----
- ----- 76. 4-varible (c) -----
- ----- 77. Minimum SOP and POS -----
- ----- 78. Karnaugh map (a) -----
- ----- 79. Karnaugh map (b) -----
- ----- 80. K-map implemented with a multiplexer -----
----- 73. 3-varible -----
Problem Statement
（三变量卡诺图）
Implement the circuit described by the Karnaugh map below.
Answer
一个非常容易化简的卡诺图，因此这里仅放出化简后的逻辑表达式，图就不放了：
out' = a'b'c' or out = (a'b'c')' （撇号表示取反，乘积表示与运算，加法表示或运算）
module top_module(
input a,
input b,
input c,
output out );
assign out = ~(~a & ~b & ~c);
endmodule
----- 74. 4-varible (a) -----
Problem Statement
（四变量卡诺图）
Implement the circuit described by the Karnaugh map below.
Answer
out = a'd' + b'c' + a'bc + acd
module top_module(
input a,
input b,
input c,
input d,
output out );
assign out = (~a & ~d) | (~b & ~c) | (~a & b & c) | (a & c & d);
endmodule
----- 75. 4-varible (b) -----
Problem Statement
（四变量带有约束条件的卡诺图）
Implement the circuit described by the Karnaugh map below.
Answer
out = b'c + a
module top_module(
input a,
input b,
input c,
input d,
output out );
assign out = (~b & c) | a;
endmodule
----- 76. 4-varible (c) -----
Problem Statement
（四变量卡诺图）
Implement the circuit described by the Karnaugh map below.
Answer
（这道题貌似只能硬解，但是也有更巧妙的办法，如下所示）
module top_module(
input a,
input b,
input c,
input d,
output out );
assign out = a + b + c + d;
endmodule
----- 77. Minimum SOP and POS -----
Problem Statement
A single-output digital system with four inputs (a,b,c,d) generates a logic-1 when 2, 7, or 15 appears on the inputs, and a logic-0 when 0, 1, 4, 5, 6, 9, 10, 13, or 14 appears. The input conditions for the numbers 3, 8, 11, and 12 never occur in this system. For example, 7 corresponds to a,b,c,d being set to 0,1,1,1, respectively.
Determine the output out_sop in minimum SOP(Sum of Product，最小项表达式（与或式）：积之和) form, and the output out_pos in minimum POS(Product of Sum，最大项表达式（或与式）：和之积) form.
Answer
由题意画出卡诺图：
化简卡诺图：
out_sop = cd + a'b'c
out_pos = ( (c'+ d')·(a + b + c') )'
（POS式我懒得化简了。。。）
module top_module (
input a,
input b,
input c,
input d,
output out_sop,
output out_pos
);
assign out_sop = (c & d) | (~a & ~b & c);
assign out_pos = ~( (~c | ~d) & (a | b | ~c) );
endmodule
----- 78. Karnaugh map (a) -----
Problem Statement
Consider the function f shown in the Karnaugh map below.
Implement this function. d is don't-care, which means you may choose to output whatever value is convenient.
Answer
f = x1'x3 + x2x4
module top_module (
input [4:1] x,
output f );
assign f = (~x[1] & x[3]) | (x[2] & x[4]);
endmodule
----- 79. Karnaugh map (b) -----
Problem Statement
Consider the function f shown in the Karnaugh map below. Implement this function.
(The original exam question asked for simplified SOP and POS forms of the function.)
Answer
f = x2'x4' + x1'x3 + x2x3x4
module top_module (
input [4:1] x,
output f
);
assign f = (~x[2] & ~x[4]) | (~x[1] & x[3]) | (x[2] & x[3] & x[4]);
endmodule
----- 80. K-map implemented with a multiplexer -----
Problem Statement
（批注：比较新颖的题目，用多路选择器实现卡诺图运算。需要注意的是，题目仅要求写出c、d的实现，并且只能使用多个二选一）
For the following Karnaugh map, give the circuit implementation（实现，执行） using one 4-to-1 multiplexer and as many 2-to-1 multiplexers as required, but using as few as possible. You are not allowed to use any other logic gate and you must use a and b as the multiplexer selector inputs, as shown on the 4-to-1 multiplexer below.
You are implementing（实现） just the portion labelled top_module, such that the entire circuit (including the 4-to-1 mux) implements the K-map.
(The requirement to use only 2-to-1 multiplexers exists because the original exam question also wanted to test logic function simplification using K-maps and how to synthesize logic functions using only multiplexers with constant inputs. If you wish to treat this as purely a Verilog exercise, you may ignore this constraint and write the module any way you wish.)
Answer
（本题思路灵感来源于《FPGA原理和结构》P57，可查阅“香农展开定理”）
先说一下初步的思路：观察卡诺图，可以这么看，当cd = 00时，mux[3:0] = 0100（注意卡诺图的顺序和代码的不一致）；当cd = 01时，mux[3:0] = 0001；当cd = 10时，mux[3:0] = 0101；当cd = 11时，mux[3:0] = 1001。
初步思路有了以后，其实大家已经发现了，这就是一个类似于选择器一样的东西，即输入cd，根据cd的值来输出对应mux的值。不过问题在于，我们要使用的是二选一选择器，而且应该至少要使用4个吧。列出表总结一下：
cd | mux[3] (f3) | mux[2] (f2) | mux[1] (f1) | mux[0] (f0) |
00 | 0 | 1 | 0 | 0 |
01 | 0 | 0 | 0 | 1 |
10 | 0 | 1 | 0 | 1 |
11 | 1 | 0 | 0 | 1 |
接着我们照表写出四个逻辑表达式：
f3 = cd
f2 = c'd' + cd' = d'
f1 = 0 （这个最简单了嘿嘿）
f0 = (c'd')' = c + d
然后需要将以上四个逻辑表达式化为二选一表达式（即f = sel'·a + sel·b的形式）：
f3 = c·d （对照二选一表达式：sel = c, a = 0, b = d)
f2 = d' （对照二选一表达式：sel = d, a = 1, b = 0)
f1 = 0 （不需要使用选择器了）
f0 = c + d （暂时还想不到用二选一实现的办法，直接用或门吧)
最后实现电路：
module top_module (
input c,
input d,
output [3:0] mux_in
);
mux21 ex3(.sel(c), .a(0), .b(d), .out(mux_in[3]));
mux21 ex2(.sel(d), .a(1), .b(0), .out(mux_in[2]));
assign mux_in[1] = 0;
assign mux_in[0] = c | d;
endmodule
module mux21 (
input sel,
input a, b,
output reg out
);
always @(*) begin
case(sel)
1'b0: out = a;
1'b1: out = b;
endcase
end
endmodule
