GNS3中PIX的激活使用
下面是激活过程
pixfirewall> en
Password:
pixfirewall# sh version
Cisco PIX Security Appliance Software Version 7.2(2)
Compiled on Wed 22-Nov-06 14:16 by builders
System p_w_picpath file is "Unknown, monitor mode tftp booted p_w_picpath"
Config file at boot was "startup-config"
pixfirewall up 3 mins 23 secs
Hardware: PIX-525, 256 MB RAM, CPU Pentium II 1 MHz
Flash E28F128J3 @ 0xfff00000, 16MB
BIOS Flash AM29F400B @ 0xfffd8000, 32KB
0: Ext: Ethernet0 : address is 0000.abcd.ef00, irq 9
1: Ext: Ethernet1 : address is 0000.abcd.ef01, irq 11
2: Ext: Ethernet2 : address is 0000.abcd.ef02, irq 11
3: Ext: Ethernet3 : address is 0000.abcd.ef03, irq 11
4: Ext: Ethernet4 : address is 0000.abcd.ef04, irq 11
The Running Activation Key is not valid, using default settings:
Licensed features for this platform:
Maximum Physical Interfaces : 6
Maximum VLANs : 25
Inside Hosts : Unlimited
Failover : Disabled //Failover不可用
×××-DES : Disabled
×××-3DES-AES : Disabled
Cut-through Proxy : Enabled
Guards : Enabled
URL Filtering : Enabled
Security Contexts : 0
GTP/GPRS : Disabled
××× Peers : Unlimited
This platform has a Restricted (R) license.
Serial Number: 808102688 //序列号
Running Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 //激活码
Configuration has not been modified since last system restart.
pixfirewall# activation-key 0xd2390d2c 0x9fc4b36d 0x98442d99 0xeef7d8b1 //输入激活码
The following features available in flash activation key are NOT
available in new activation key:
Failover is different.
flash activation key: Restricted(R)
new activation key: Unrestricted(UR)
Proceed with update flash activation key? [confirm] （直接回车）
The following features available in running activation key are NOT
available in new activation key:
Failover is different.
running activation key: Restricted(R)
new activation key: Unrestricted(UR)
WARNING: The running activation key was not updated with the requested key.
The flash activation key was updated with the requested key, and will
become active after the next reload.
pixfirewall# write //保存配置
Building configuration...
Cryptochecksum: 70b1d47e d807251d 47f50cb7 f851d390
1226 bytes copied in 0.800 secs
[OK]
然后在GNS3中直接停掉PIX，重新启动即可，不能reload。
下面是重启后的
pixfirewall> en
Password:
pixfirewall# sh version
Cisco PIX Security Appliance Software Version 7.2(2)
Compiled on Wed 22-Nov-06 14:16 by builders
System p_w_picpath file is "Unknown, monitor mode tftp booted p_w_picpath"
Config file at boot was "startup-config"
pixfirewall up 17 secs
Hardware: PIX-525, 256 MB RAM, CPU Pentium II 1 MHz
Flash E28F128J3 @ 0xfff00000, 16MB
BIOS Flash AM29F400B @ 0xfffd8000, 32KB
0: Ext: Ethernet0 : address is 0000.abcd.ef00, irq 9
1: Ext: Ethernet1 : address is 0000.abcd.ef01, irq 11
2: Ext: Ethernet2 : address is 0000.abcd.ef02, irq 11
3: Ext: Ethernet3 : address is 0000.abcd.ef03, irq 11
4: Ext: Ethernet4 : address is 0000.abcd.ef04, irq 11
Licensed features for this platform:
Maximum Physical Interfaces : 10
Maximum VLANs : 100
Inside Hosts : Unlimited
Failover : Active/Active
×××-DES : Enabled （激活了）
×××-3DES-AES : Enabled
Cut-through Proxy : Enabled
Guards : Enabled
URL Filtering : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
××× Peers : Unlimited
This platform has an Unrestricted (UR) license.
Serial Number: 808102688
Running Activation Key: 0xd2390d2c 0x9fc4b36d 0x98442d99 0xeef7d8b1
Configuration has not been modified since last system restart.
附上我找到的PIX序列号&激活码
PIX序列号
Serial Number:0x302aab20
Activation Key:0xd2390d2c 0x9fc4b36d 0x98442d99 0xeef7d8b1
Serial Number:0x1c9f971c
Activation Key:0xa94b7db5,0x17d768ea,0x63f6e081,0x6d9fadd5
Serial Number:808102688
Activation Key:0xd2390d2c 0x9fc4b36d 0x98442d99 0xeef7d8b1
Serial Number:0x301D10D9
Activation Key:0x5236f5a7 0x97def6da 0x732a91f5 0xf5deef57
笔者视频http://www.tudou.com/programs/view/Y3SH915hJEg/?resourceId=80111054_03_0_01
